NetPing Supply Voltage Sensor 995S2

A sensor allows detecting the power voltage in the power outlet.

  • it is manufactured in the case of the power unit with the IEC320 C7 (IP20) socket. It can be plugged into any outlet using a detachable power cord;
  • has the internal nodes powered from the grid and thus may maintain operation in the range between AC 70…250 V with the frequency of 50/60 Hz;
  • Triggering threshold: 178–193 V;
  • Releasing threshold: 155–175 V;
  • The output type is «dry contact» / normally closed and normally opened contacts (built-in relay);
  • Loop is 1,5 meter long.

Description

Name Status Price, $
NetPing Supply Voltage Sensor 995S2 ACTIVE 21

General usage conditions - for industrial and commercial usage in conditions of high humidity (0-95%, non-condensing). The device is not intended for domestic use.

A sensor allows determining only the presence or absence of the voltage in the power outlet. A sensor does not determine the value of the voltage in the power outlet!

The output of the sensor is normally closed and normally opened relay contacts («dry contact», three wires: a normally closed wire — a common wire — a normally opened wire). When the voltage is below 65–78 V, relay contacts are opened. When the voltage exceeds 80–93 V, the state of the contacts is changed to the opposite.

A sensor is connected to the contacts IO and GND of the NetPing devices depending on which logic level is needed when there is no voltage. The connection polarity of the wires from the sensors is irrelevant.

The information about connecting a sensor is indicated in the document named «User Guide» that is specific for every device that is connected to the sensor. The configuration information about a sensor and its functionality is specified in the document named «Firmware Description» that is specific for every device that is connected to the sensor.

If there is a need to determine if there is the voltage in a 3-phase circuit, ensure there are three power outlets, one for each phase, and use three power sensors.

A sensor is shipped with an inseparable cord with the tips at the ends. A length of a cord can be increased using loop extenders for the sensor RC-4 that are plugged one into another or independently using any wire with a cross-section of no less than 0,4 square millimeters. Ideally, a maximum allowed loop length is 100 meters.

Specification

Solution

The device is intended for indoor use only

indoor only

Formfactor and enclosure

compact plastic case

Warning

NetPing Supply Voltage Sensor 995S2 allows determining only the presence or absence of the voltage in the power outlet. A sensor does not determine the value of the voltage in the power outlet!

NetPing Supply Voltage Sensor 995S2 has the internal nodes powered from the grid.

The device maintains operation in the range between AC 70…250 V with the frequency of 50/60 Hz.

Triggering threshold:

178–193 V

Releasing threshold:

155–175 V

A sensor is shipped with an inseparable cord with the tips at the ends. A length of a cord can be increased using loop extenders for the sensor RC-4 that are plugged one into another or independently using any wire with a cross-section of no less than 0,4 square millimeters.

The maximum allowed loop length is 100 meter

Functionalities

Main functionalities

The output of the NetPing Supply Voltage Sensor 995S2 is normally closed and normally opened relay contacts («dry contact», three wires: a normally closed wire — a common wire — a normally opened wire.

When the voltage is below 65–78 V, relay contacts are opened. When the voltage exceeds 80–93 V, the state of the contacts is changed to the opposite.

A sensor is connected to the contacts IO and GND of the NetPing devices depending on which logic level is needed when there is no voltage.

The connection polarity of the wires from the sensors is irrelevant.

State of output contacts

NO and NC

Possibility to monitor power quality in a three-phase circuit, and output three power outlets from each phase.

Yes, but only the presence or absence of voltage on the phase

Hardware specification

Connectors

«dry contact», three wires: a normally closed wire — a common wire — a normally opened wire

The information about connecting a sensor is indicated in the document named «User Guide»

Power supply and parameters

Power supply of a sensor

Powered by a controlled electrical outlet

Dimensions and logistics parameters

Water proof case

No

Lenght of a non-removable cable

1,5 meter

Device dimensions (W x D x H)

80 x 45 x 25 mm

Package box dimensions (W x D x H)

Bag ZIP (Number 8), 170×240 mm

Net weight

101 g

Unit packaged weight (transportation weight)

190 g

Device packing containment

NetPing Supply Voltage Sensor 995S2 — 1 pc.; quick start guide — 1 pc.; power cord IEC320 C7 to CEE7 XVII (SL-5+SL-8), 1,8 meter — 1 pc.; packing box + name sticker — 1 pc.

Operating conditions

Ambient air temperature for operation

-30°С … +50°С

Relative humidity

5…95 % (relative humidity has to be not more than 95%, non-condensing)

Operating atmospheric pressure range

84,0 … 106,7 kPa

Storage conditions

Ambient air temperature for storage

-40°С … +85°С

Storage Relative Humidity

5…95 %

Device reliability

Mean Time Between Failures, MTBF

35 000 h

Estimated life expactancy of the product

At least 3 years

Limited manufacturer’s warranty

3 years from production date

Lifetime technical support

Yes

Documentation and files

Manuals

How to Buy?

You can purchase all equipment offered at our website for USD directly from us NetPing east Co Ltd. company or from our official partners. All prices indicated on our website are current ones.

To purchase NetPing devices, email please your request to sales@netpingdevice.com. In the email, indicate please the next:

  • Name and number of models of devices that you want to purchase. Do not forget to indicate sensors and accessories that are necessary for you.
  • Company name and a name of the recipient of the parcel with equipment.
  • Complete mailing address for equipment delivery.
  • Contacts (e-mail and a phone number).

Afterwards, a sales manager will prepare and send you an invoice in USD to pay the order (the details of our bank account and PayPal account are specified on the invoice). The invoice is valid for 10 days, and if you do not pay it within the specified time frame, the invoice will be canceled. To renew the order, you will need to send a repeat request to a sales manager.

Equipment can be sold for 100% prepayment only!

We make discounts to retail customers. Provided by lot (lot - one time buying/shipment):

  • Lot total amount > 600 USD → 5% discount.
  • Lot total amount > 1500 USD → 10% discount.
  • Lot total amount > 3000 USD → special discount.

We deliver equipment to any country of the world for free. Free delivery of devices without batteries is provided by EMS company. Free delivery of devices with batteries is provided by DHL company.

Customers from Russian Federation are welcome to visit our Russian website www.netping.ru and choose there a more convenient method to purchase our goods.

Compatible devices