NetPing Light Sensor 813S2

NetPing Light Sensor 813S2 is a compact luminous flux presence sensor designed to connect with NetPing devices.

Threshold adjustment 10–7000 Lx.
An adjustment step 10–300 Lx.
A viewing angle 25–30°.
Hysteresis 20%.
Sensor triggering/release time from 1 s up to 20 s.
An output type NPN, an open drain/dry contact connected to an IO-line of a NetPing device.
An operating temperature range -30…+50°С without moisture condensation.

Description

General usage conditions - for industrial and commercial usage in conditions of high humidity (0-95%, non-condensing). The device is not intended for domestic use.

This sensor can monitor the sudden emerging of artificial lighting in guarded objects, as well as back up an operation of a door sensor.

You can effectively use it at the following facilities:

server rooms;
data centers;
base transmission stations (cell towers);
rooms with equipment;
storehouses;
guarded objects.

The device also allows remote monitoring of the presence of luminous flux and automatically control light sources depending on the level of illumination of the surrounding space of the following objects:

residential buildings;
premises of administrative buildings;
banking and insurance institutions;
educational and preschool institutions;
leisure centers;
general catering establishments;
shops;
consumer services enterprises;
hotels;
hospitals, pharmacies;
transport tunnels.

The device is made on an electronic board in a compact case (the width is 15 mm, the length is 68 mm). In order to increase reliability, electronic components of the sensor are covered with a polymer film. In order to install it easily, a hole with a diameter of 5 mm is made in the sensor case, and a self-adhesive surface is applied.

The device board has two LEDs indicating the operating mode, the green one – “day”, the red one – “night”. The design of the device includes an SW level switch that switches the measuring sensor to different response ranges, as well as a trimmer potentiometer RV1 to correct the sensor response.

The sensor is connected to I/O lines of monitoring units.

The information of connecting the sensor is specified in the “User Guide” for the device connected to the sensor. For information about the sensor configuration and functionality, refer to the Firmware Description for the device to which you will connect the sensor.

The length of the loop from the sensor to a host device should not exceed 100 m. If it is necessary for you, you can extend the length of the native loop with Cable 4 extender, 4m or you can use any wire with a cross-section of at least 0.4 mm².

Specification

Functionalities
Solution
The device is not intended for any domestic use	for industrial and commercial use in conditions of high humidity (0-95%, non-condensing)
The device is intended for indoor use only	indoor only
Formfactor and enclosure	The device is made on an electronic board in a compact case (the width is 15 mm, the length is 68 mm). In order to increase reliability, electronic components of the sensor are covered with a polymer film.
Simplified mounting	In order to install it easily, a hole with a diameter of 5 mm is made in the sensor case, and a self-adhesive surface is applied.
The length of the loop from the sensor to a host device.	maximum length is 100 meter
Main functionalities
The device also allows remote monitoring of the presence of luminous flux and automatically controls light sources depending on the level of illumination of the surrounding space of different objects.	wide range of applications (different types of premises and facilities)
Illumination measurement range	1-10000 Lx
Threshold adjustment	10–7000 Lx
Minimum threshold	3-5 Lx
Adjustment step	10–300 Lx
Viewing angle	25–30°
Hysteresis	20%
Sensor triggering/release time	from 1s to 20s depending on the illumination level
Hardware specification
Connectors
The sensor is connected (to a monitoring unit) with the help of:	IO-line
Options to extend the sensor’s loop	It is possible to extend the length of the native loop with Cable 4 extender of 4 meter, or simply by use of any wire with a cross-section of at least 0.4 mm².
Control and display
The device board has two LEDs indicating the operating mode:	the green one – “day”, the red one – “night”
Additional adjustment options	The design of the device includes an SW level switch that switches the measuring sensor to different response ranges, as well as a trimmer potentiometer RV1 to correct the sensor response.
Power supply and parameters
Power supply of a sensor	5V
Nominal current	no more than 10 mA
Interface, socket	аn output type NPN, an open drain/dry contact connected to an IO-line of a NetPing device
Dimensions and logistics parameters
Water proof case	No
Lenght of the loop	3 meter
Device dimensions (W x D x H)	68 x 15 x 5 mm
Net weight	50 g
Device packing containment	Sensor, zip package
Operating conditions
Outdoor / indoor usage restriction	For indoor use only
Ambient air temperature for operation	-30°С … +50°С
Relative humidity	5…95 % (relative humidity has to be not more than 95%, non-condensing)
Operating atmospheric pressure range	84,0 … 106,7 kPa
Storage conditions
Ambient air temperature for storage	-40°С … +85°С
Storage Relative Humidity	5…95 %
Device reliability
Mean time between failures	35 000 h
Device life	At least 3 years
Limited manufacturer’s warranty	3 years from production date
Lifetime technical support	Yes

Documentation and files

Manuals

NetPing Light Sensor 813S2, User Guide

1 file(s) 448.59 KB

Download

How to Buy?

You can purchase all equipment offered at our website for USD directly from us NetPing east Co Ltd. company or from our official partners. All prices indicated on our website are current ones.

To purchase NetPing devices, email please your request to sales@netpingdevice.com. In the email, indicate please the next:

Name and number of models of devices that you want to purchase. Do not forget to indicate sensors and accessories that are necessary for you.
Company name and a name of the recipient of the parcel with equipment.
Complete mailing address for equipment delivery.
Contacts (e-mail and a phone number).

Afterwards, a sales manager will prepare and send you an invoice in USD to pay the order (the details of our bank account and PayPal account are specified on the invoice). The invoice is valid for 10 days, and if you do not pay it within the specified time frame, the invoice will be canceled. To renew the order, you will need to send a repeat request to a sales manager.

Equipment can be sold for 100% prepayment only!

We make discounts to retail customers. Provided by lot (lot - one time buying/shipment):

Lot total amount > 600 USD → 5% discount.
Lot total amount > 1500 USD → 10% discount.
Lot total amount > 3000 USD → special discount.

We deliver equipment to any country of the world for free. Free delivery of devices without batteries is provided by EMS company. Free delivery of devices with batteries is provided by DHL company.

Customers from Russian Federation are welcome to visit our Russian website www.netping.ru and choose there a more convenient method to purchase our goods.

Compatible devices

Cable 4 extender, 4m

NetPing 2 IP PDU ETH 53R14

NetPing 2 IP PDU ETH R2

NetPing 2 IP PDU GSM3G 203R15

NetPing 2 IP PDU GSM3G R2

NetPing 4 IP PDU ETH R8

NetPing 4 IP PDU GSM3G 64R701

NetPing 4 IP PDU GSM3G 64R702

NetPing 4 IP PDU GSM3G R8

NetPing 4 IP PDU GSM3G R9

NetPing 8 IP PDU ETH R8

NetPing 8 IP PDU ETH R9

NetPing 8 IP PDU GSM3G R8

NetPing 8 IP PDU GSM3G R9

NetPing Input+Relay R404

NetPing Input+Relay R504

NetPing Input+Relay R704

NetPing IO R401

NetPing Monitor M1

NetPing Monitoring Solution GSM3G R61

NetPing Monitoring Solution R61